bopm setup

BOPM Proxy Bot Installing Tutorial

/*
* Full path and filename for storing the process ID of the running
* BOPM.
*/
pidfile = "/some/path/bopm.pid"; <--- Path where your BOPM is installed with bopm.pid
(ex. /home/yourusername/bopm/bopm.pid)


* Amount of file descriptors to allocate to asynchronous DNS. 64
* should be plenty for almost anyone - previous versions of BOPM only
* did one at a time!
*/
dns_fdlimit = 64; <--- Leave it as it is.


* Put the full path and filename of a logfile here if you wish to log
* every scan done. Normally BOPM only logs successfully detected
* proxies in the bopm.log, but you may get abuse reports to your ISP
* about portscanning. Being able to show that it was BOPM that did
* the scan in question can be useful. Leave commented for no
* logging.
*/
# scanlog = "/some/path/scan.log"; <--- Leave it as it is. Or set it to where u want to save ur logs (ex./home/yourusername/bopm/bopm.pid)
};



/*
* IP to bind to for the IRC connection. You only need to use this if
* you wish BOPM to use a particular interface (virtual host, IP
* alias, ...) when connecting to the IRC server. There is another
* "vhost" setting in the scan {} block below for the actual
* portscans. Note that this directive expects an IP address, not a
* hostname. Please leave this commented out if you do not
* understand what it does, as most people don't need it.
*/
# vhost = "0.0.0.0"; <--- Leave it as it is or put the ip your shell company provide you with.



/*
* Nickname for BOPM to use.
*/
nick = "MyBopm"; <--- IRC Nickname for your Proxy Bot.

/*
* Text to appear in the "realname" field of BOPM's /whois output.
*/
realname = "Blitzed Open Proxy Monitor"; <--- Realname for your Proxy Bot.

/*
* If you don't have an identd running, what username to use.
*/
username = "bopm"; <--- Username "ident" for your Proxy Bot.

* Hostname (or IP) of the IRC server which BOPM will monitor
* connections on.
*/
server = "myserver.somenetwork.org"; <--- Name of your IRCD Server (ex. irc.ircfuture.net)


/*
* Password used to connect to the IRC server (PASS)
*/

# password = "secret"; <--- Password for connect.
password = "serverpass:opernick:operpass"; <<< If you want the bot join as an oper
/*
* Port of the above server to connect to. This is what BOPM uses to
* get onto IRC itself, it is nothing to do with what ports/protocols
* are scanned, nor do you need to list every port your ircd listens
* on.
*/
port = 6667; <--- Server Port. or any other port u require

/*
* Command to execute to identify to NickServ (if your network uses
* it). This is the raw IRC command text, and the below example
* corresponds to "/msg nickserv identify password" in a client. If
* you don't understand, just edit "password" in the line below to be
* your BOPM's nick password. Leave commented out if you don't need
* to identify to NickServ.
*/
# nickserv = "privmsg nickserv :identify password"; <--- If you are going to use registered nickname for you Proxy bot then first remove # from the start of the line and change password with password of registered nickname.

/*
* The username and password needed for BOPM to oper up.
*/
oper = "bopm operpass"; <--- IRCOP Nickname\Password for Proxy Bot.



* Channel name. Local ("&") channels are supported if your ircd
* supports them.
*/
name = "#bopm";
key ="channel key";

Look down for target_string and change to
target_string = ":basement.fi.eu.ircfuture.net NOTICE AUTH :*** Looking up your hostname..."; << change the server
target_string = "ERROR :Trying to reconnect too fast.";
target_string = "ERROR :Your host is trying to (re)connect too fast -- throttled.";

# AANOTE good to have
exempt {
mask = "*!*@127.0.0.1";
mask = "*!*@ircfuturenet"; <
};

Then save your work and exit

1. cd ../bin
2. ./bopm

go top